Goodsense forklift new generation diesel counter balance forklift advantages:
1.Strong Power System.GOODSENSE forklifts are all with reliable power accessories.All accessories like engine, gear box are support by domestic and world famous brand, high quality, reliable after-sales.We follow the strict environmental design,all engines match the China â…¢ or even higher emission standards.
2.Super comfortable.GOODSENSE forklifts are all with comfortable driving space,adjustable steering wheel and seats,super low and non-slip step,suspension steering axle,storing space,and convenient LCD panel.
3.High Security.Whole perspective mast and backrest, super good view,high strength overhead guard,high place security combination lamp,neutral security features,parking brake,fork lock function(optional),all for safety.
General
Model
FD30
FD35
Power Type
Diesel
Diesel
Load Capacity
kg
3000
3500
Load centre
mm
500
500
Tyre
Tyre
Pneumatic Tyre
Pneumatic Tyre
Front Tyre
28*9-15-12PR
28*9-15-12PR
Rear Tyre
6.50-10-10PR
6.50-10-10PR
Overall Dimension
Lift Height
mm
3000
3000
Fork Size
L×W×T
mm
1070*125*45
1070*125*50
Mast Tilt Angle
F/R
.
6/12
6/12
Mast Lowered Height
mm
2115
2115
Mast Extended Height(with backrest)
mm
4175
4150
Length to face of fork(Without fork)
mm
2710
2750
Overall Width
mm
1225
1225
Overhead Guard Height
mm
2090
2090
Application Area:
1.Warehouse
2.Port
3.Factory
4.Distribution Center
5.Logistics
If you have any other questions,please contact us directly.Our forklift are all with high quality,and you can choose any other engine to equip.It can be produced according to your idea.And we invite you to visit our factory.
3.0-3.5Ton Diesel Forklift,3.0 On Diesel Forklift,3.5Ton Diesel Forklift ZHEJIANG GOODSENSE FORKLIFT CO.,LTD , https://www.goodsenseforklift.com
Grade
Density
T.R.S MPa
Hardness HRA
Performance & application recommended
YG6A
14.95
1800
92.5
Fine grain alloy, good wear resistance. Semifinishing of chilled cast iron, non-ferrors metals alloys, semi-finishing and finishing of hardened steel, alloy steel.
YG8
14.80
2200
89.5
High strength in use, impact and shock resistance higher than YG6, but wear resistance and cutting speed comparatively lower. Roughing of cast irons, non-ferrors metals and their alloys as well as non metallic materials at low cutting speed.
YG10X
14.5
2400
91.5
Fine grain alloy, good wear resistance. Used for processing hard wood, veneer board, PCB, PVC and metals.
YL10.2
14.5
2400
91.8
Fine grade alloy, with high wear resistance, high bending strength, high resistance to bonding, high thermal strength. Machining of refractory alloys, stainless steel and high manganese steel, etc.
G20
14.3
2420
90.0
Conventional wear resistance, high
Our customers spread all over 50 countries. We provide our customers the carbide products with good quality,competitive price,fast delivery time and reliable after sale service. To your reference, you can check more items from our website: www.zzhardmetal.cn
We supply all kinds of tungsten carbide discs, mainly used for paper, tobacco, rubber, plywood, hardwood, PCB, PVC, stainless steel, high manganese steel and PCB, PVC electronic circuit boards and and lamp tube, fiber cement board and other materials industry. Grades in: YG6A, YG8A, YG8X, YG8, YG10X, YS2T so on. These products require high precision, no glitches, no indentation phenomenon, so a larger cut of difficulty, To solve this problem, we have static pressing, HIP sintering greatly improve the physical properties of the product, polishing plating, so that when the blade cut, easy to wear and does not stick powder, reducing friction when cutting, greatly improving the accuracy and speed slitting, tool life extended, success for the user to save a lot of manpower and financial resources.
We also recommend suitable grades according to customer demand.
We make according to customer's drawings.
High precision circular disc cutter, round-cut blades (high wear / sharp / stainless)
1, Tolerance: High Availability to diameter (± 0.01) * Thickness (± 0.005) * inner diameter (H7) * balance (± 0.005)
2, Hardness: HRC64 ° ~ 66 ° And HRC68 ° ~70 °
3, Features: Cutting blade requires precision diameter, thickness, straightness, etc. Customized are also welcomed!
Carbide Discs Description:
Carbide Discs is mainly used for paper, rubber, plywood, hardwood, PCB, PVC, stainless steel, high manganese steel and PCB, PVC electronic circuit boards and other materials industry.
Materials: YG6A, YG8A, YG8X, YG8, YG10X, YS2T and so on.
These products require high precision, no glitches, maximum abrasion resistance. We are using HIP sintered and fine grinding, polishing plating to reduce frictions when cutting, improved the accuracy and speed slitting greatly, tool life extended!
Grades:
YG8 and YS2T are widely used for making carbide cutting disc. But other size can be offered by your requirement.
Grade properties:
YG8: High strength in use, impact and shock resistance higher than YG6, but wear resistance and cutting speed comparatively lower. Roughing of cast irons, non-ferrors metals and their alloys as well as non metallic materials at low cutting speed.
YS2T: Fine grade alloy, with high wear resistance, high bending strength, high resistance to bonding, high thermal strength. Machining of refractory alloys, stainless steel and high manganese steel, etc.
ZZ HARDMETAL provides the followings as a guide to satisfy you:
Availability
Durability
Rust resistance
Cutting process
Costs
Edge geometry
Wear resistance
Ways to identify good carbide disc
1. Sound checking: Before installing the blade, hang the blade with fingers. Gently knock with a wooden hammer, listen to sounds, it is cracked if muddy sound, prohibited to use if cracked, in order to avoid accidents!
2. Running speed: Make sure the cutting speed is in or below 4800 rev/min.
3. Blade install: When installing, rotating shaft and blade center requires accurate alignment of the blade, clean the mechanical mounting surfaces, no cutting material, dust or other debris to be left on blades.
4. Install protective devices: You must install the protective cover (blades should baffle around the studio, steel, rubber and other protective equipment) before the blade running.
Â
Grade
Density
T.R.S MPa
Hardness HRA
Performance & application recommended
YG6A
14.95
1800
92.5
Fine grain alloy, good wear resistance. Semifinishing of chilled cast iron, non-ferrors metals alloys, semi-finishing and finishing of hardened steel, alloy steel.
YG8
14.80
2200
89.5
High strength in use, impact and shock resistance higher than YG6, but wear resistance and cutting speed comparatively lower. Roughing of cast irons, non-ferrors metals and their alloys as well as non metallic materials at low cutting speed.
YG10X
14.5
2400
91.5
Fine grain alloy, good wear resistance. Used for processing hard wood, veneer board, PCB, PVC and metals.
YL10.2
14.5
2400
91.8
Fine grade alloy, with high wear resistance, high bending strength, high resistance to bonding, high thermal strength. Machining of refractory alloys, stainless steel and high manganese steel, etc.
G20
14.3
2420
90.0
Conventional wear resistance, high
Our customers spread all over 50 countries. We provide our customers the carbide products with good quality,competitive price,fast delivery time and reliable after sale service. To your reference, you can check more items from our website: www.zzhardmetal.cn
We supply all kinds of tungsten carbide discs, mainly used for paper, tobacco, rubber, plywood, hardwood, PCB, PVC, stainless steel, high manganese steel and PCB, PVC electronic circuit boards and and lamp tube, fiber cement board and other materials industry. Grades in: YG6A, YG8A, YG8X, YG8, YG10X, YS2T so on. These products require high precision, no glitches, no indentation phenomenon, so a larger cut of difficulty, To solve this problem, we have static pressing, HIP sintering greatly improve the physical properties of the product, polishing plating, so that when the blade cut, easy to wear and does not stick powder, reducing friction when cutting, greatly improving the accuracy and speed slitting, tool life extended, success for the user to save a lot of manpower and financial resources.
We also recommend suitable grades according to customer demand.
We make according to customer's drawings.
High precision circular disc cutter, round-cut blades (high wear / sharp / stainless)
1, Tolerance: High Availability to diameter (± 0.01) * Thickness (± 0.005) * inner diameter (H7) * balance (± 0.005)
2, Hardness: HRC64 ° ~ 66 ° And HRC68 ° ~70 °
3, Features: Cutting blade requires precision diameter, thickness, straightness, etc. Customized are also welcomed!
Carbide Discs Description:
Carbide Discs is mainly used for paper, rubber, plywood, hardwood, PCB, PVC, stainless steel, high manganese steel and PCB, PVC electronic circuit boards and other materials industry.
Materials: YG6A, YG8A, YG8X, YG8, YG10X, YS2T and so on.
These products require high precision, no glitches, maximum abrasion resistance. We are using HIP sintered and fine grinding, polishing plating to reduce frictions when cutting, improved the accuracy and speed slitting greatly, tool life extended!
Grades:
YG8 and YS2T are widely used for making carbide cutting disc. But other size can be offered by your requirement.
Grade properties:
YG8: High strength in use, impact and shock resistance higher than YG6, but wear resistance and cutting speed comparatively lower. Roughing of cast irons, non-ferrors metals and their alloys as well as non metallic materials at low cutting speed.
YS2T: Fine grade alloy, with high wear resistance, high bending strength, high resistance to bonding, high thermal strength. Machining of refractory alloys, stainless steel and high manganese steel, etc.
ZZ HARDMETAL provides the followings as a guide to satisfy you:
Availability
Durability
Rust resistance
Cutting process
Costs
Edge geometry
Wear resistance
Ways to identify good carbide disc
1. Sound checking: Before installing the blade, hang the blade with fingers. Gently knock with a wooden hammer, listen to sounds, it is cracked if muddy sound, prohibited to use if cracked, in order to avoid accidents!
2. Running speed: Make sure the cutting speed is in or below 4800 rev/min.
3. Blade install: When installing, rotating shaft and blade center requires accurate alignment of the blade, clean the mechanical mounting surfaces, no cutting material, dust or other debris to be left on blades.
4. Install protective devices: You must install the protective cover (blades should baffle around the studio, steel, rubber and other protective equipment) before the blade running.
Â
Tungsten Cemented Carbide Disc for Cutting Steel
Model NO.: Many Types
Trademark: ZZ HARDMETAL
Specification: many
Origin: China
HS Code: 82090010
Model NO.: Many Types
Trademark: ZZ HARDMETAL
Specification: many
Origin: China
HS Code: 82090010